Intel i210 driver

Intel i210 driver DEFAULT

Linux Base Driver for Intel(R) Ethernet Network Connection¶

Intel Gigabit Linux driver. Copyright(c) 1999-2018 Intel Corporation.

Contents¶

  • Identifying Your Adapter

  • Command Line Parameters

  • Additional Configurations

  • Support

Identifying Your Adapter¶

For information on how to identify your adapter, and for the latest Intel network drivers, refer to the Intel Support website: https://www.intel.com/support

Command Line Parameters¶

If the driver is built as a module, the following optional parameters are used by entering them on the command line with the modprobe command using this syntax:

modprobe igb [<option>=<VAL1>,<VAL2>,...]

There needs to be a <VAL#> for each network port in the system supported by this driver. The values will be applied to each instance, in function order. For example:

In this case, there are two network ports supported by igb in the system.

NOTE: A descriptor describes a data buffer and attributes related to the data buffer. This information is accessed by the hardware.

max_vfs¶

Valid Range

0-7

This parameter adds support for SR-IOV. It causes the driver to spawn up to max_vfs worth of virtual functions. If the value is greater than 0 it will also force the VMDq parameter to be 1 or more.

The parameters for the driver are referenced by position. Thus, if you have a dual port adapter, or more than one adapter in your system, and want N virtual functions per port, you must specify a number for each port with each parameter separated by a comma. For example:

This will spawn 4 VFs on the first port.

This will spawn 2 VFs on the first port and 4 VFs on the second port.

NOTE: Caution must be used in loading the driver with these parameters. Depending on your system configuration, number of slots, etc., it is impossible to predict in all cases where the positions would be on the command line.

NOTE: Neither the device nor the driver control how VFs are mapped into config space. Bus layout will vary by operating system. On operating systems that support it, you can check sysfs to find the mapping.

NOTE: When either SR-IOV mode or VMDq mode is enabled, hardware VLAN filtering and VLAN tag stripping/insertion will remain enabled. Please remove the old VLAN filter before the new VLAN filter is added. For example:

ip link set eth0 vf 0 vlan 100 // set vlan 100 for VF 0 ip link set eth0 vf 0 vlan 0 // Delete vlan 100 ip link set eth0 vf 0 vlan 200 // set a new vlan 200 for VF 0

Debug¶

Valid Range

0-16 (0=none,…,16=all)

Default Value

0

This parameter adjusts the level debug messages displayed in the system logs.

Additional Features and Configurations¶

Jumbo Frames¶

Jumbo Frames support is enabled by changing the Maximum Transmission Unit (MTU) to a value larger than the default value of 1500.

Use the ifconfig command to increase the MTU size. For example, enter the following where <x> is the interface number:

ifconfig eth<x> mtu 9000 up

Alternatively, you can use the ip command as follows:

ip link set mtu 9000 dev eth<x> ip link set up dev eth<x>

This setting is not saved across reboots. The setting change can be made permanent by adding ‘MTU=9000’ to the file:

  • For RHEL: /etc/sysconfig/network-scripts/ifcfg-eth<x>

  • For SLES: /etc/sysconfig/network/<config_file>

NOTE: The maximum MTU setting for Jumbo Frames is 9216. This value coincides with the maximum Jumbo Frames size of 9234 bytes.

NOTE: Using Jumbo frames at 10 or 100 Mbps is not supported and may result in poor performance or loss of link.

Enabling Wake on LAN (WoL)¶

WoL is configured through the ethtool utility.

WoL will be enabled on the system during the next shut down or reboot. For this driver version, in order to enable WoL, the igb driver must be loaded prior to shutting down or suspending the system.

NOTE: Wake on LAN is only supported on port A of multi-port devices. Also Wake On LAN is not supported for the following device: - Intel(R) Gigabit VT Quad Port Server Adapter

Multiqueue¶

In this mode, a separate MSI-X vector is allocated for each queue and one for “other” interrupts such as link status change and errors. All interrupts are throttled via interrupt moderation. Interrupt moderation must be used to avoid interrupt storms while the driver is processing one interrupt. The moderation value should be at least as large as the expected time for the driver to process an interrupt. Multiqueue is off by default.

REQUIREMENTS: MSI-X support is required for Multiqueue. If MSI-X is not found, the system will fallback to MSI or to Legacy interrupts. This driver supports receive multiqueue on all kernels that support MSI-X.

NOTE: On some kernels a reboot is required to switch between single queue mode and multiqueue mode or vice-versa.

MAC and VLAN anti-spoofing feature¶

When a malicious driver attempts to send a spoofed packet, it is dropped by the hardware and not transmitted.

An interrupt is sent to the PF driver notifying it of the spoof attempt. When a spoofed packet is detected, the PF driver will send the following message to the system log (displayed by the “dmesg” command): Spoof event(s) detected on VF(n), where n = the VF that attempted to do the spoofing

Credit Based Shaper (Qav Mode)¶

When enabling the CBS qdisc in the hardware offload mode, traffic shaping using the CBS (described in the IEEE 802.1Q-2018 Section 8.6.8.2 and discussed in the Annex L) algorithm will run in the i210 controller, so it’s more accurate and uses less CPU.

When using offloaded CBS, and the traffic rate obeys the configured rate (doesn’t go above it), CBS should have little to no effect in the latency.

The offloaded version of the algorithm has some limits, caused by how the idle slope is expressed in the adapter’s registers. It can only represent idle slopes in 16.38431 kbps units, which means that if a idle slope of 2576kbps is requested, the controller will be configured to use a idle slope of ~2589 kbps, because the driver rounds the value up. For more details, see the comments on .

NOTE: This feature is exclusive to i210 models.


© Copyright The kernel development community.

Built with Sphinx using a theme provided by Read the Docs.
Sours: https://www.kernel.org/doc/html/v5.12/networking/device_drivers/ethernet/intel/igb.html

Back to Scan Result

Intel(R) I210 Gigabit Network Connection Driver for Supermicro - X10SAE working on

Device Name:

Intel(R) I210 Gigabit Network Connection

Hardware ID:

PCI\VEN_8086&DEV_1533&SUBSYS_153315D9&REV_03
PCI\VEN_8086&DEV_1533&SUBSYS_153315D9 <---- Device ID matches with our database
PCI\VEN_8086&DEV_1533&CC_020000
PCI\VEN_8086&DEV_1533&CC_0200


Compatible ID:
PCI\VEN_8086&DEV_1533&REV_03
PCI\VEN_8086&DEV_1533
PCI\VEN_8086&CC_020000
PCI\VEN_8086&CC_0200
PCI\VEN_8086
PCI\CC_020000
PCI\CC_0200

Version:

12.8.26.0,2013-07-12

List of driver files that match with the above device in our database.

You are viewing the drivers of an anonymous computer which may be not the same with your current computer. These driver(s) may not work with your computer. Please click on the link below to download, scan and get the correct drivers.

Why do i see many drivers ?
Below is a list of drivers that may be suitable for your device. With the different devices, they can have the same driver , it's because they all use the same chip manufacturer.

How to select driver?
If you are looking for an update , pickup the latest one. If your driver isn't working, use the driver having the same OEM with the your laptop/desktop brand name.
Watch this video to see how it works - click here

*: 2K=Windows 2000, 2K3= Windows 2003 , XP= Windows XP , VISTA = Windows Vista , WIN7 = Windows 7,WIN10= Windows 10

Intel(R) I210 Gigabit Network Connection

hp

sp114064.exe

12.18.12.1

2021-02-23

1.43 MB

WIN10/64bits

Download

Intel(R) I210 Gigabit Network Connection

intel

25_4.zip

12.16.3.1

2020-07-16

610.17 MB

WIN10/64bits

Download

Intel(R) I210 Gigabit Network Connection

intel

PROWinx64.zip

12.16.3.1

2020-07-16

60.93 MB

WIN10/64bits

Download

Intel(R) I210 Gigabit Network Connection

msi

lan-25.4.zip

12.16.3.1

2020-07-16

105.2 MB

WIN10/64bits

Download

Intel(R) I210 Gigabit Network Connection

Others

PRO_v25.5.zip

12.16.3.1

2020-07-16

652.64 MB

WIN10/64bits

Download


All company and product names/logos used herein may be trademarks of their respective owners and are used for the benefit of those owners. All Rights Reserved. Privacy Policy

Sours: https://www.driveridentifier.com/scan/intelr-i210-gigabit-network-connection-driver/download/1325412469/F381072997194F688663FFB58541D2F9/PCI%5CVEN_8086%26DEV_1533%26SUBSYS_153315D9
  1. Methodist churches omaha ne
  2. Volkswagen cobb
  3. Double cola bottles value
  4. Lexus 460 car
  5. Ephesians message bible

Windows 10 intel i210 network connection driver drivers

Intel I210 Gigabit Network Connection Driver 12.12.226.0 for Windows 10 64-bit Apr 23, 2016

The package provides the installation files for Intel I210 Gigabit Network Connection Driver version 12.12.226.0. If the driver is already installed on your system, updating (overwrite-installing) ... consideration that is not recommended to install the driver on Operating Systems other than stated ones. In order to manually update your driver, follow the steps below (the next steps): ...

Intel I210 Gigabit Network Connection Driver 12.12.226.0 for Windows 10 Apr 23, 2016

The package provides the installation files for Intel I210 Gigabit Network Connection Driver version 12.12.226.0. If the driver is already installed on your system, updating (overwrite-installing) ... consideration that is not recommended to install the driver on Operating Systems other than stated ones. In order to manually update your driver, follow the steps below (the next steps): ...

Intel I210 Gigabit Network Connection Driver 12.15.184.0 for Windows 10 Anniversary Update Mar 30, 2017

If the driver is already installed on your system, updating (overwrite-installing) ... consideration that is not recommended to install the driver on Operating Systems other than stated ones. In order to manually update your driver, follow the steps below (the next steps): 1. ... device you wish to update and choose Update Driver Software 4. Choose to select the location of ...

Intel PROSet/Network Adapter Driver 26.4 for Windows 10 64-bit Aug 3, 2021

... New in This Release:- Microsoft Windows support for Intel Ethernet Network Adapter E810-2C-Q2  - Base drivers for Intel Ethernet 800 Series devices now support firmware ... Support for Red Hat Enterprise Linux (RHEL) 8.4. Drivers are no longer tested on RHEL 8.3. - Support for FreeBSD 13.0. Drivers are no longer tested on FreeBSD 11.4. ...

Intel Network Adapter Driver 26.4 for Windows 10 64-bit Aug 3, 2021

... New in This Release:- Microsoft Windows support for Intel Ethernet Network Adapter E810-2C-Q2  - Base drivers for Intel Ethernet 800 Series devices now support firmware ... Support for Red Hat Enterprise Linux (RHEL) 8.4. Drivers are no longer tested on RHEL 8.3. - Support for FreeBSD 13.0. Drivers are no longer tested on FreeBSD 11.4. ...

Intel Network Adapter Driver 20.1 for Windows 10 Jun 19, 2015

Installs base drivers, Intel PROSet Software for Windows Device Manager, advanced networking services (ANS) for teaming and VLANs, and SNMP for Intel Network Adapters for this operating system only.What's New in ... Release: - Linux support for VXLAN Overlay on Intel Ethernet Controller X552-based devices - Support for the Intel Ethernet Connection X552/X557-AT 10GBASE-T - As of ...

Similar intel i210 network connection driver drivers for Windows 10 keywords:

intel avstream camera 2500 driverintel iris pro graphics driverintel i219-lm ethernet driverintel i210 network driverintel nuc p14e network connection driverintel i211 network connection driverintel i217-v ethernet driverintel wireless gigabit device driverintel nuc5cpyh nuc graphics driverintel high definition graphics driverintel i350 f1 network connection driverintel nuc5pgyh nuc graphics driverintel i210 t1 network connection driverintel stk2m3w64cc hd graphics driverintel i210 network connection driverintel smart sound technology driverintel i350 network connection driverintel i219-v ethernet driverintel i218-v ethernet driverintel i218-lm ethernet driver


Sours: https://drivers.windows10download.com/win10-intel-i210-network-connection-driver-drivers/
Intel QuickAssist: How to install driver in CentOS 7 Linux

Download the self-extracting archive and run it. When you run it, it will extract the files to a temporary directory, run the installation wizard, and remove the temporary files when the installation is complete. All language files are embedded in this archive. You do not need to download an extra language pack.

See readme.htm if you want to extract the files without installing.

This software may also apply to Intel Ethernet Controllers. Support for built-in network connections is provided by the system or board manufacturer.

The software drivers provided on this page are generic versions and can be used for general purposes. However, computer original equipment manufacturers (OEMs) may have altered the features, incorporated customizations, or made other changes to the software or software packaging they provide. To avoid any potential installation incompatibilities on your OEM system, Intel recommends that you check with your OEM and use the software provided via your system manufacturer. Intel or the computer original equipment manufacturer (OEM) may not provide technical support for some or all issues that could arise from the usage of this generic version of software drivers.

What's New:

Supported Products:

  • Intel 82599EB 10 Gigabit Ethernet Controller
  • Intel 82599EN 10 Gigabit Ethernet Controller
  • Intel 82599ES 10 Gigabit Ethernet Controller
  • Intel Ethernet Connection I217-LM
  • Intel Ethernet Connection I217-V
  • Intel Ethernet Connection I218-LM
  • Intel Ethernet Connection I218-V
  • Intel Ethernet Connection I219-LM
  • Intel Ethernet Connection I219-V
  • Intel Ethernet Controller I210-AS
  • Intel Ethernet Controller I210-AT
  • Intel Ethernet Controller I210-CS
  • Intel Ethernet Controller I210-IS
  • Intel Ethernet Controller I210-IT
  • Intel Ethernet Controller I211-AT
  • Intel Ethernet Controller I225-LM
  • Intel Ethernet Controller I225-V
  • Intel Ethernet Controller I350-AM2
  • Intel Ethernet Controller I350-AM4
  • Intel Ethernet Controller I350-BT2
  • Intel Ethernet Controller X540-AT2
  • Intel Ethernet Controller X540-BT2
  • Intel Ethernet Controller X550-AT
  • Intel Ethernet Controller X550-AT2
  • Intel Ethernet Controller X550-BT2
  • Intel Ethernet Converged Network Adapter X520-DA1
  • Intel Ethernet Converged Network Adapter X520-DA2
  • Intel Ethernet Converged Network Adapter X520-LR1
  • Intel Ethernet Converged Network Adapter X520-QDA1
  • Intel Ethernet Converged Network Adapter X520-SR1
  • Intel Ethernet Converged Network Adapter X520-SR2
  • Intel Ethernet Converged Network Adapter X520-T2
  • Intel Ethernet Converged Network Adapter X540-T1
  • Intel Ethernet Converged Network Adapter X540-T2
  • Intel Ethernet Converged Network Adapter X550-T1
  • Intel Ethernet Converged Network Adapter X550-T2
  • Intel Ethernet Network Adapter X722-DA2
  • Intel Ethernet Network Adapter X722-DA4
  • Intel Ethernet Server Adapter I210-T1
  • Intel Ethernet Server Adapter I350-F2
  • Intel Ethernet Server Adapter I350-F4
  • Intel Ethernet Server Adapter I350-T2
  • Intel Ethernet Server Adapter I350-T2V2
  • Intel Ethernet Server Adapter I350-T4V2

Previous versions:

Here's other similar drivers that are different versions or releases for different operating systems:

    ▸ Browse all Intel drivers

    Sours: https://www.techspot.com/downloads/drivers/essentials/intel-network-adapter/

    Driver intel i210

    Updated Driver Is Required to iSCSI Boot Windows Server Using Intel i210 Gigabit Ethernet Connection

    Bug ID: 25534023

    Issue: There is a mismatch between the inbox Intel i210 Gigabit Ethernet driver used during Windows Server setup and the inbox Intel i210 Gigabit Ethernet driver used in the Windows Server operating system. When performing an iSCSI installation using the Intel i210 Gigabit Ethernet connection, the driver mismatch results in a failure to boot the installed Windows Server OS.

    Affected Software: Microsoft Windows Server 2012 R2 and Windows Server 2016

    Workaround: You must install one of the following newer drivers during server setup:

    • Windows Server 2012 R2 driver INF file:

    • Windows Server 2016 driver INF file:

    These driver files are located in .

    Sours: https://docs.oracle.com/en/servers/x86/x7-2l/product-notes/grzve.html
    Unboxing: Winyao I210T PCI-E - chipset Intel I210-AT

    INTRODUCTION

    This component demonstrates various features of the Intel I210 Ethernet controller. These features can be used for developing Audio/Video Bridging applications, Industrial Ethernet applications which require precise timing control over frame transmission, or test harnesses for measuring system latencies and sampling events.

    This component - igb_avb - is limited to the Intel I210 Ethernet controller. The kernel module can be loaded in parallel to existing in-kernel igb modules which may be used on other supported Intel LAN controllers. Modifications are required to the in-kernel drivers if the existing in-kernel igb driver has support for the Intel I210.

    BUILDING

    The kernel igb module should be built which supports the latest Linux kernel 3.x PTP clock support. Unlike the standard igb driver, this version enables PTP by default (and will fail to build without kernel PTP support enabled).

    RUNNING

    To install the kernel mode driver, you must have root permissions. Typically, the driver is loaded by removing the currently running igb and running igb_avb: sudo rmmod igb sudo modprobe i2c_algo_bit sudo modprobe dca sudo modprobe ptp sudo insmod ./igb_avb.ko

    Another option is to install the igb_avb driver in the "updates" directory which will override igb for the other drivers claiming the same device ID. This will allow the coexistence of igb and igb_avb. Copy igb_avb.ko to: sudo cp igb_avb.ko /lib/modules//updates/ sudo depmod -a modprobe igb_avb

    As the AVB Transmit queues (0,1) are mapped to a user-space application, typical LAN traffic must be steered away from these queues. The driver implements one method registering an ndo_select_queue handler to map traffic to queue[3]. Another possibly faster method uses the the transmit packet steering (XPS) functionality available since 2.6.35. An example script is below

    #!/bin/bash

    INTERFACE=p2p1 export INTERFACE

    rmmod igb rmmod igb_avb insmod ./igb_avb.ko sleep 1 ifconfig $INTERFACE down echo 0 > /sys/class/net/$INTERFACE/queues/tx-0/xps_cpus echo 0 > /sys/class/net/$INTERFACE/queues/tx-1/xps_cpus echo f > /sys/class/net/$INTERFACE/queues/tx-2/xps_cpus echo f > /sys/class/net/$INTERFACE/queues/tx-3/xps_cpus ifconfig $INTERFACE up

    You map also want to disable the network manager from 'managing' your interface. The easiest way is to find the interface configuration scripts on your distribution. On Fedora 18, these are located at /etc/sysconfig/network-scripts/ifcfg-. Edit the file to set 'BOOTPROTO=none'. This eliminates DHCP trying to configure the interface while you may be doing user-space application configuration.

    Sours: https://github.com/Avnu/igb_avb

    You will also like:

    Intel I210 and I211 driver update

    I know this isn’t a new topic, but it’s a pretty important one.
    I work for a non-profit company and we’ve gone with urbackup as it is perfect for our needs, not because it’s free, but because it’s simple and straightforward.

    I’m trying to do a proof of concept for my supervisor and i have two workstations, one with the Intel I210AT ethernet contoller and another with an intel I211. it seems that neither of these are supported.

    It seems that the drivers are available for download so that they can be compiled and incorporated into the version of debian that makes up the restore CD. is there any way you can do that? or am i just not doing something correct? I’ve attempted this with a usb-based ethernet adapter, different speed usb ports, different builds of the restore CD. the only one that seems to work is one of the two ports on one of the test systems is a realtek… it works with that, but it goes dead with the intels.

    Thanks for devoting yourselves in making such great software!

    Sours: https://forums.urbackup.org/t/intel-i210-and-i211-driver-update/10392


    295 296 297 298 299